Refiller For The Canon Pro1 Pgi-29 Tanks

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,822
Reaction score
8,852
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
OK here is an update on my progress for refilling these new PGI-29 cartridge tanks.
After a number of failures I have come up with a fairly easy solution to the problem.

Anyone can make up this refilling tip from any of your needles in your refilling arsenal.
I am going to call The Hat Tip refilling method for argument sake because thats all it is.

Just take a needle then twist and pull out the steel section from the plastic holder and your half way there.
Next put the needless base onto a syringe just for safety sake and cut, trim off the little winglets on either side of the base till they are smooth.

5128_new_tips_2.png


If you fit this to a larger 60 ml syringe you now have the new refiller.
You can either fill your syringe first or later it doesnt matter just fit your new tip to the end of the syringe and your ready to refill.

Here is an up-date on this procedure.
Since making this thread I have revised the method slightly so now the cartridge needs to be on bottom with the syringe on top.
There is no need to remove any of the ink from the cartridge only the air and thats accomplished
better if the syringe is held above the cartridge and follow this procedure instead (Link Below).
http://www.printerknowledge.com/threads/revised-refill-for-pro-1-cartridge-with-photos-part-2.8670/



5128_cartridge_fill.jpg



These cartridges are as easy to refill as the PGI9 cartridge with almost the same methods used just a different gadget on the syringe that all.
Now all I got to do is find out where I can get all of the inks from.. :)
 
Last edited:

stratman

Printer VIP
Platinum Printer Member
Joined
Apr 19, 2007
Messages
8,706
Reaction score
7,170
Points
393
Location
USA
Printer Model
Canon MB5120, Pencil
Looks good uncle The Hat, but how do we get the plastic to change shape and go from magenta to yellow? You are a master alchemist! :bow
 

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,822
Reaction score
8,852
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
stratman said:
Looks good uncle The Hat, but how do we get the plastic to change shape and go from magenta to yellow? You are a master alchemist! :bow
Drugs stratman simply Drugs:lol:
 

rodbam

Printer Master
Joined
Mar 9, 2011
Messages
773
Reaction score
173
Points
213
Location
Australia
Printer Model
Canon Pro 9000 mk2 & Pro 9500
Hats said:
I am going to call The Hat Tip refilling method for argument sake because thats all it is.
I would call it The Tip of the Hat Method.
Do you have a Pro1 & how do you like it?
What about resetting the cart chips?
 

websnail

Printer VIP
Platinum Printer Member
Joined
Oct 27, 2005
Messages
3,666
Reaction score
1,349
Points
337
Location
South Yorks, UK
Printer Model
Epson, Canon, HP... A "few"
Wondering if the old Epson Bottom Fill adapter do the job a little better...
 

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,822
Reaction score
8,852
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
I would call it The Tip of the Hat Method.
Do you have a Pro1 & how do you like it?
What about resetting the cart chips?
Hats off to rodbam, well the tip anyway.

No I dont have one yet but am working on the wife, hope she cracks soon dough. :hugs :fl
I dont really care if there is no chip resetter for these printers because the cartridges are so big,
I will probably just use a scales till an ARC chip is available.
websnail

Wondering if the old Epson Bottom Fill adapter do the job a little better...
Any information on this bottom filler and where to get it would be appreciated
all dough I think it might not be long enough to make contact with the piston but would give it a try anyway.
Everything little helps, thanks Martin.. :)
 

llama_91

Getting Fingers Dirty
Joined
Feb 29, 2012
Messages
25
Reaction score
0
Points
27
Location
Queensland, Australia.
@The Hat.

I haven't seen one of these cartridges before but your refill method looks very similar to the way i fill the old epson cartridges (t0491's etc.) Have you tried using a small piece of flat rubber and puncturing a hole through it with a syringe? then you just need to shorten the needle to the appropriate length (i use a Stanley knife to cut around the needle until it's weak enough to snap off with pliers.) It should create a good seal and make it easier to change between colours. Hope this helps!
 

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,822
Reaction score
8,852
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
llama_91 said:
@The Hat.

I haven't seen one of these cartridges before but your refill method looks very similar to the way i fill the old epson cartridges (t0491's etc.) Have you tried using a small piece of flat rubber and puncturing a hole through it with a syringe? then you just need to shorten the needle to the appropriate length (i use a Stanley knife to cut around the needle until it's weak enough to snap off with pliers.) It should create a good seal and make it easier to change between colours. Hope this helps!
I have tried lots of different way to refill these cartridge tanks, its not the refilling that's the problem, it's the air that’s introduced into the bag when refilling, it must be released last.

I didn't try your method before but will certainly have a go with it, every little bit helps thanks..:)
 

sneezer2

Getting Fingers Dirty
Joined
Jul 31, 2009
Messages
79
Reaction score
10
Points
36
Location
USA Pennsylvania
Printer Model
mp610
Looks almost like the old BJI-643 cartridges (of which I still have several).
 

ink hatter

Newbie to Printing
Joined
Apr 24, 2012
Messages
1
Reaction score
0
Points
6
Ok Now the cartridges been filled
How do we over come the chip Can this be reset or do you over ride it
If over rideing the chip what is the sequence to do this :D
 
Top